https://orbxsystems.com/forum/topic/...ow-2-released/
Didn't see this posted yet so I'll slip it in . Funny , I just opted into the Beta Object Flow a few days ago .
Rich
https://orbxsystems.com/forum/topic/...ow-2-released/
Didn't see this posted yet so I'll slip it in . Funny , I just opted into the Beta Object Flow a few days ago .
Rich
USAF Retired , 906 Tactical Fighter Group , Wright Patterson AFB , Ohio
I7-9700K , MSI/MPG-Z390M , 32GB DDR4 3200 , RTX 2080 8GB
Just to round this up:
The update also goes along with a new FTX Central version "FTX Central v3.2.3.0" and contains various V4 specific updates.
Cheers,
Mark
My scenery development galleries:
https://www.dropbox.com/sh/x0skkam7xu8zz8r/DFwnonB1nH
Solomon 1943 V2 Open beta download: http://www.sim-outhouse.com/download...on-1943-V2.zip
Solomon 1943 V2 update 2013-02-05 download: http://www.sim-outhouse.com/download...2013-02-05.zip
Current Project: DHC-4 / C-7a Caribou by Tailored Radials
Dev-Gallery at https://www.dropbox.com/sh/qjdtcoxeg...bAG-2V4Ja?dl=0
Finally!
I’ll back to my FTX airports! Didnt install beta before so it was big break, near 5 months from June!
Great!
Webmaster of yoyosims.pl.
Win 10 64, i9 13900 KF, RTX 4090 24Gb, RAM64Gb, SSD M.2 NVMe, Predator XB271HU res.2560x1440 27'' G-sync, Sound Blaster Z + 5.1, TiR5 [MSFS, P3Dv5, DCS, RoF, Condor, IL-2 CoD/BoX] VR fly only: Meta Quest Pro
+1 to YoYo, +1 to Sue ... at least it made it in time for winter in Minnesota (when I do most of my sim flying).
Not to hijack the thread, but I will be looking to do some formation with some folks. Any recommendations from the assemblage as to how it works with P3D v4 and who is doing it? Thanks.
Jay
USNR-Ret; Former Airline Migratory Worker; Builder, Owner, Operator RV-8 N817J
Comp Spec - ASRock Steel Legend WiFi M/B, Ryzen 7 5800X, RX 6900 XT, 32GB RAM, M2 SSD for DCS, SATA SSD for MSFS2020
I installed the beta last week. I don't recall seeing the final install but it must have done when opening and closing FTX Central (fixing annoying elevation issues) and it says now v 3.2.3.0 and the box is checked saying "use ObjectFlow 2 in Prep 3D v4"
Would others agree or do am I missing another necessary step (e.g. downloading the whole - final - shabang again . . )?
Striker, listen, and you listen close: flying a plane is no different than riding a bicycle, just a lot harder to put baseball cards in the spokes.
expat, your description of how they upgraded to v3.2.3.0 is exactly the way things went for me. The upgrade uses Object Flow v2 if you check the settings. Usually I see an upgrade notice on the left side but didn't seem to happen this time.
Regards, Tom Stovall KRDD
My FTX Central updated in a similar fashion as expat's. I have about 20 NA airports and downloaded them, ran the airport configuration tool and loaded P3D v4. I chose to do a quick flight out of Redding, CA and ,oh boy, looking very nice. Even taxiing around the airport was interesting (remember...P3D is not for fun).
Jay
USNR-Ret; Former Airline Migratory Worker; Builder, Owner, Operator RV-8 N817J
Comp Spec - ASRock Steel Legend WiFi M/B, Ryzen 7 5800X, RX 6900 XT, 32GB RAM, M2 SSD for DCS, SATA SSD for MSFS2020
My scenery development galleries:
https://www.dropbox.com/sh/x0skkam7xu8zz8r/DFwnonB1nH
Solomon 1943 V2 Open beta download: http://www.sim-outhouse.com/download...on-1943-V2.zip
Solomon 1943 V2 update 2013-02-05 download: http://www.sim-outhouse.com/download...2013-02-05.zip
Current Project: DHC-4 / C-7a Caribou by Tailored Radials
Dev-Gallery at https://www.dropbox.com/sh/qjdtcoxeg...bAG-2V4Ja?dl=0
Bookmarks